• Inspect tow coupling condition and check mounting bolts are tight. (80 ftlbs)
• Lubricate tow coupling & jockey wheel grease nipples if fitted
• Inspect jockey wheel condition and operation
• Lubricate & adjust jockey wheel mount pivot clearance
• Inspect condition of control arm bushes
• Inspect control arms for cracks or damage
• Check camber bolts are tight. (80 ftlbs)
• Inspect bump stops for overloading witness marks
• Check camber pin welds and report if cracked and repair where required
• Before removing wheel, check wheel bearing free play & note on job card if loose
• Adjust brakes as per instructions below
• Inspect chassis gusset brackets for cracks (front & rear of wheel arch) repair if required
• Check Anderson and trailer plug condition, replace if required
• Check trailer light operation, reflectors & report if faulty
• Check tyre pressures & condition of wear (including spare) rec. Pressure 40 PSI (Odyssey) 45PSI (Quant/Eclipse/Matrix/Aurora)
• Check tyre carrier operation & security. (clean and grease if required)
• Check roof scissors bolts, gas strut pop rivets & solar cable are sealed
• Positive Pressure Vent filter. (blow out or replace if required)
• Check wheel nuts with torque wrench. (155nm)
• Get all your work checked by the Workshop Supervisor, return job card and keys to the Service Manager

• Inspect tow coupling condition and check mounting bolts are tight. (80 ftlbs)
• Lubricate tow coupling & jockey wheel grease nipples if fitted
• Inspect jockey wheel condition and operation
• Lubricate & adjust jockey wheel mount pivot clearance
• Inspect condition of control arm bushes
• Inspect control arms for cracks or damage
• Check camber bolts are tight. (80 ftlbs)
• Remove shocks, extend & compress fully checking smoothness
• Inspect shock bolts/bushes for wear and lube with graphite grease only. Replace Nuts
• Inspect bump stops for overloading witness marks
• Check camber pin welds and report if cracked and repair where required
• Before removing wheel, check wheel bearing free play & note on job card if loose
• Remove hubs, service bearings, inspect & replace if required, replace seals (note parts on job card)
• Check brake drums for high spots or loose bearing cups etc
• Inspect brake shoes and note on job card percentage of wear remaining
• Adjust brakes as per instructions below
• Inspect chassis gusset brackets for cracks (front & rear of wheel arch) repair if required
• For disc brakes grease slider pins with appropriate grease, check tightness of calliper bolts
• Check Anderson and trailer plug condition, replace if required
• Check trailer light operation, reflectors & report if faulty
• Check tyre pressures & condition of wear (including spare) rec. Pressure 40 PSI (Odyssey) 45PSI (Quant/Eclipse/Matrix/Aurora)
• Check tyre carrier operation & security. (clean and grease if required)
• Lubricate caravan stabilizer & leg pivots. (clean of mud etc first if required)
• Lubricate all key locks (kitchen, fridge, hot water system, toolbox etc.)
• Check condition of gas bottles, gas lines and fittings (stone damage etc)
• Lubricate roof scissor lifts runners. (top and bottom)
• Check roof scissors bolts, gas strut pop rivets & solar cable are sealed
• Positive Pressure Vent filter. (blow out or replace if required)
• Check wheel nuts with torque wrench. (155nm)
• Check the quality of the step and make sure it is placed back in the van step area
• Get all your work checked by the Workshop Supervisor, return job card and keys to the Service Manager

• Car auto electrical modifications
• Trailer auto electrical modifications
• Inspection & Diagnosis of electrical issues
• Solar charging modificationS

• Upgrade toilet system
• Fit additional solar panel
• Ceramic Pro
• Retrofit aircon & diesel heater
• Retrofit grey or extra water tank

We can undertake all types of services  for all other brands

• Routine 10,000 km service
• Upgrades
• Pre- sales checks
• Brakes
• Warranty work
• Water tanks
• Solar
• Amenities
  and more